7215A REV B Norge Dryer Parts List

Refrigerator ice and water filter (filter canister)

Replacement ice maker

This 8-cube ice maker is used to help produce ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze the water until ice cubes are formed. Once the water has been frozen the ice cubes will be ejected from the mold into the ice bucket and will refill with water to repeat the process until the ice bucket is full. This ice maker does not include the bail or shut off arm. You can reuse the arms for your old ice maker or you can also order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. The harness can be reused. This ice maker will not fit refrigerators that have the ice auger mounted on the door. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Bake element - 220v 2300w (oven bake heating element with screw-on terminals. The element is 18-1/4 inches wide, 14-1/2 inches deep to mounting flange. Terminal ends extend 2-1/)

This closed-hinged style bottom bake element is located on the bottom of the oven cavity to supply the heat for baking. This bake element has screw-on wire terminals is 18 1/4-inch wide and 14 1/2-inch deep to mounting flange and the terminal ends extend 2 1/2-inch past the flange. The element is 2300 watts and 20 volts. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. This is a genuine OEM bake element. Please remember to disconnect the power to your oven before you start your repair.

Door catch kit (use wpl 279570)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Suspension spring

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be off balance and noisy. Check your model to see how many springs are required for your model. The spring is sold individually.

Upper roller and axle - kit of 4 (roller and stud asm (4pk))

The upper roller and axle attach to the upper rack to allow the dishrack to move in and out along the track of the dishwasher. This is a kit includes 4 rollers and 4 axles for your upper rack. If your dish rack is not moving in and out of the dishwasher properly you may have a broken or missing wheel and it will need to be replaced. The rollers and axles are made out of plastic and are white in color. This is a genuine OEM kit.

Drive belt (belt drive)

This dryer drum drive belt is 89.5" long and has four ribs. This part helps spin the drum during the drying cycle.

Lower spray arm (lower spray arm with shields)

Lower front dishrack wheel (front roller & stud)

This wheel is located on the front lower rack. It includes the axle. Sold individually.

Dryer drum support roller (support)

The drum support roller has a metallic bearing in its center. This part is used to hold the drum in place in the cabinet while letting the drum rotate on the support rollers. If your dryer is noisy, will not tumble or takes too long to dry, you might need to replace the roller. It is recommended that you replace both rollers at once. This is a genuine OEM part and is sold individually. Please remember to shut off the power to the dryer before starting the repair.

Flat style oven igniter kit (sub 12400035)

The flat style gas oven igniter is used to ignite the gas to light the oven burner, which produces heat for your range. If the element has shorted out, is no longer glowing, or is glowing but only orange or red rather than white, then you will need to replace the oven igniter. When replacing the igniter please be very careful not to touch the gray element part of the igniter as it is very fragile. The igniter measures approximately 3-3/4"in length and the amperage range is 3.3 to 3.6. This igniter kit can replace igniters for either the broil or bake burners and can replace shorter and longer igniters. The kit includes the igniter, 4 wire nuts, insulation, 2 wire assembly and a bracket. This is a genuine OEM part. Please make sure to disconnect the power and shut off the gas supply before starting your repair.

Dishwasher upper rack adjuster (adjuster arm)

Drawer slide rail - right side (slide asm rh)

This replacement drawer slide rail is for the right-hand side of your refrigerator. This part attaches to the inside wall of your refrigerator to support the sliding crisper drawer. If the rail is broken or the drawer is not sliding properly, you will need to replace the slide rail. You will need a Phillips screwdriver to complete this repair.

Door strike (striker)

This is a door strike for your washing machine. It is the piece that activates the door switch once the door is closed. If your washer will not start, will not fill with water, or the door will not open/close you may need to replace the door strike. This part is white in color, made from plastic, and measures approximately 2 1/2 inches. This is a genuine OEM part.

Terminal block kit (bracket)

This surface burner terminal block kit comes with interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing and wires. This part is used to connect the wire harness to the surface burner element. If your element will not heat at all, or is not heating properly, it is likely an issue with the terminal block and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power supply before starting your repair.